Hood does not pop up when pulling latch

aloofbit · 07-24-2021, 02:41 PM

Hi! I was wondering is the hood supposed to stay flat when pulling the hood open lever under the dash?

On my other cars when I pull the hood open lever the hood springs up about an inch then I can pull the front latch to open.

On my Z4 when I pull the lever under the dashboard the hood stays flat and I have to put my finger in the the corner above the headlight to pull it up a little to then pull the second latch and the hood floats up with the lifters.

Coi · 07-24-2021, 08:36 PM

The hood on my 07 Z4 pops up a little when I pull the latch. Not sure what the mechanism is that makes it happen.

inTgr8r · 07-24-2021, 10:07 PM

aloofbit

There are two spring loaded "buffer pins" that commonly fail.
see #14

Name: Screen Shot 2021-07-24 at 10.04.29 PM.png
Views: 422
Size: 472.0 KB

aloofbit · 07-24-2021, 11:34 PM

yay! ty ty ty, I will try and get these

wdb · 08-11-2021, 11:39 AM

Those were bad on both of my Z4s. I just reach under and lift.

SD ///M4 · 08-27-2021, 01:23 PM

Quote:

Originally Posted by aloofbit

yay! ty ty ty, I will try and get these

Did you replace these? Does the hood lift any higher when released?

3002 tii · 09-09-2021, 08:30 PM

On my 3.0si coupe it was smooth as butter. On the M, there’s a lot of tension in the hood release lever, almost like it’s going to snap.

Piper1 · 09-09-2021, 09:11 PM

Prefacelift are different than post latches. Both my 03 and 07 pop up when pulled. I’m sure there’s a thread deep down somewhere but pre the latches get a bit corrodie from the elements being in the front with rain snow salt and grit from the road causing very sticky latches. Post there’s the D style latch relocated to the sides instead of right next to the front lever release. If you have a prefacelift some white lithium sprayed periodically and good cleaning can keep the front latch from getting sticky.

Polarbert · 11-03-2021, 09:29 PM

Mine never popped up all that much. I bought two of these to replace the old buffer stops that no longer raised up.

https://www.ebay.com/itm/162291088365

mif280 · 01-17-2022, 04:57 AM

I recently order a pair of these rubber buffers with ejectors from my dealer. The original ones contained springs to push up the electors but the bottoms appear to be blown out probably from years of use.

The same ejectors can also be installed on the rear lid of the e85 to pop it up a bit higher upon opening. The OEM rubber buffers on the back don't normally have ejectors so you can swap them out.

07-24-2021, 02:41 PM	#1
aloofbit New Member 2 Rep 6 Posts Drives: BMW Z4 M Join Date: Jun 2021 Location: Chicago iTrader: (0)	Hood does not pop up when pulling latch Hi! I was wondering is the hood supposed to stay flat when pulling the hood open lever under the dash? On my other cars when I pull the hood open lever the hood springs up about an inch then I can pull the front latch to open. On my Z4 when I pull the lever under the dashboard the hood stays flat and I have to put my finger in the the corner above the headlight to pull it up a little to then pull the second latch and the hood floats up with the lifters.
	Appreciate 0 Tweet Quote

07-24-2021, 08:36 PM	#2
Coi First Lieutenant 302 Rep 323 Posts Drives: 21 X3 M40i, 07 Z4MR Join Date: Mar 2021 Location: Cal iTrader: (0)	The hood on my 07 Z4 pops up a little when I pull the latch. Not sure what the mechanism is that makes it happen.
	Appreciate 0 Quote

07-24-2021, 10:07 PM	#3
inTgr8r Lieutenant General 2455 Rep 11,667 Posts Drives: M2 Comp Join Date: Mar 2006 Location: Toronto iTrader: (10)	aloofbit There are two spring loaded "buffer pins" that commonly fail. see #14
	Appreciate 1 kaybat127.50 Quote

07-24-2021, 11:34 PM	#4
aloofbit New Member 2 Rep 6 Posts Drives: BMW Z4 M Join Date: Jun 2021 Location: Chicago iTrader: (0)	yay! ty ty ty, I will try and get these
	Appreciate 0 Quote

08-11-2021, 11:39 AM	#5
wdb dances with roads 5106 Rep 4,132 Posts Drives: '07 E86, '02 996, '95 Seven Join Date: Jul 2015 Location: the perimeter iTrader: (4)	Those were bad on both of my Z4s. I just reach under and lift.
	Appreciate 0 Quote

09-09-2021, 08:30 PM	#7
3002 tii Lieutenant General 2490 Rep 12,696 Posts Drives: Z4 M, X5, GX460 Join Date: Apr 2008 Location: CT iTrader: (100) Garage List E86 Z4 M [10.00] F15 X5 xDrive35i [9.17] F10 550i (Retired) [9.17] E85 Z4 M (Retired) [9.41] F25 X3 xDrive35i (R ... [9.43] E82 135is (Retired) [9.56] E90 328i xDrive (Re ... [9.25] E86 Z4 3.0si (Retired) [8.93]	On my 3.0si coupe it was smooth as butter. On the M, there’s a lot of tension in the hood release lever, almost like it’s going to snap. __________________ Follow for latest mods
	Appreciate 0 Quote

09-09-2021, 09:11 PM	#8
Piper1 Lieutenant 601 Rep 619 Posts Drives: E85 Join Date: Mar 2018 Location: Here and there iTrader: (2)	Prefacelift are different than post latches. Both my 03 and 07 pop up when pulled. I’m sure there’s a thread deep down somewhere but pre the latches get a bit corrodie from the elements being in the front with rain snow salt and grit from the road causing very sticky latches. Post there’s the D style latch relocated to the sides instead of right next to the front lever release. If you have a prefacelift some white lithium sprayed periodically and good cleaning can keep the front latch from getting sticky.
	Appreciate 0 Quote

11-03-2021, 09:29 PM	#9
Polarbert English Member 26 Rep 99 Posts Drives: 2006 Z4M Roadster Join Date: Aug 2015 Location: San Diego iTrader: (0) Garage List 2006 BMW Z4 M Roadster [0.00]	Mine never popped up all that much. I bought two of these to replace the old buffer stops that no longer raised up. https://www.ebay.com/itm/162291088365
	Appreciate 0 Quote

01-17-2022, 04:57 AM	#10
mif280 Registered 2 Rep 1 Posts Drives: 2006 Z4MR TiAg Join Date: Nov 2017 Location: Victoria BC Canada iTrader: (0)	I recently order a pair of these rubber buffers with ejectors from my dealer. The original ones contained springs to push up the electors but the bottoms appear to be blown out probably from years of use. The same ejectors can also be installed on the rear lid of the e85 to pop it up a bit higher upon opening. The OEM rubber buffers on the back don't normally have ejectors so you can swap them out.
	Appreciate 1 wdb5106.00 Quote

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search