ZPOST
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   ZPOST > BMW Z4 Roadster and Coupe > Z4 DIY (Do It Yourself) Articles
  TireRack

SUPPORT ZPOST BY DOING YOUR TIRERACK SHOPPING FROM THIS BANNER, THANKS!
Post Reply
 
Thread Tools Search this Thread
      07-29-2019, 10:54 AM   #1
nadaclue
Private First Class
27
Rep
139
Posts

Drives: Urban Green 2003 3.0
Join Date: Mar 2008
Location: Chicago

iTrader: (0)

Ford Mustang alternative to BMW soft top motor and pump

This is buried in various threads across Z4 forums, but I feel it deserves its own attention. The going rate for a bmw soft top motor and pump is $650 at the time I'm typing this, but there is a Ford alternative that works just as well. I recently relocated my motor and pump to the trunk using the Mustang part as follows, and it works great and is faster at raising and lowering than stock:

I just finished up my roof top motor relocation this weekend as well, I utilized the Ford Mustang motor/pump assembly too.
I'm attaching pictures of the pump assembly I used in case it helps other people out. I received the assembly with some of the wiring attached, including a disconnect so I reused that as well.

Some basic info on the pump I used:
  • Purchased for $180 off ebay.
  • It was listed being for 2008-2014 Ford Mustang.
  • Made by Hoerbiger (same as the Z4).
  • Pump assembly showed part numbers S109024 and HB80069-002P.
  • Electric motor shows part numbers 3M5042, 1090069, and HB80006-019C.
  • The fluid reservoir is about 2x the size of the BMW one, but they're interchangeable so I put the BMW reservoir on the Ford pump.
  • For wiring, Mustang red to BMW green/grey and Mustang yellow to BMW blue/grey.
  • The banjo bolts on the mustang pump are the same size as the BMW, however the inlet/outlets are on the opposite side. Meaning the holes in the bolts are on the bottom when screwed in instead of the top. I'm not sure if this matters but I reused the BMW bolts just in case.
  • The pump outlets were labeled 11/13 on one and 12/14. This runs backwards from BMW's setup (at least for my 2003)! I initially plumbed it per the numbering on the pump and it ran in reverse, the open button closed and vice versa. So I had to switch the hydraulic lines so the 11/13 were attached to the pump at 12/14 position, and the bmw lines 12/14 were at the 11/13 position on the pump. Once done, it runs correctly.
Attached Images
  
Appreciate 4
      10-01-2019, 08:17 PM   #2
SD ///M4
///Multiple
SD ///M4's Avatar
United_States
2484
Rep
3,872
Posts

Drives: M4 Coupe | M3 | Z4M Roadster
Join Date: Jan 2011
Location: San Diego, CA

iTrader: (1)

Garage List
I can't believe that it's been over 2 months and no one has commented on your post. This is excellent news for anyone who needs or may need to replace their OEM pump.

Can you post more pictures of how you mounted it in the trunk? Possible wiring/plumbing diagram?
__________________
The Coupe: 2016 M4 | Sakhir Orange | Black Full Merino Leather | CF Trim | M-DCT | More | ED 5/13/16
The Sedan: 2018 M3 | San Marino Blue | Black Full Merino Leather | CF Trim | M-DCT | ZCP | ED 7/18/18
The Roadster: 2006 Z4 | Interlagos Blue | Black Extended Nappa Leather | Carbon Leather Trim | Purchased 7/19/12

Appreciate 0
      03-01-2020, 02:00 PM   #3
Woody99
Registered
0
Rep
1
Posts

Drives: 2008 BMW Z4 si
Join Date: Mar 2019
Location: Waikoloa, Hawaii

iTrader: (0)

Mustang pump to BMW Z4

good work and a money saver.
Appreciate 0
      03-01-2020, 03:35 PM   #4
3002 tii
Lieutenant General
3002 tii's Avatar
United_States
1345
Rep
11,762
Posts

Drives: Z4M, X3 35i, i3 REx
Join Date: Apr 2008
Location: CT

iTrader: (91)

Garage List
Btw were you able to relocate the pump without taking the top out? Seems like there’s a lot of info on the boards suggesting it’s possible but no definitive DIY. And I don’t see that shop in Europe who does this offering their trade secrets anytime soon.
__________________
Follow for latest mods
Appreciate 0
      03-02-2020, 07:56 PM   #5
deemo319
Major
deemo319's Avatar
United_States
1138
Rep
1,371
Posts

Drives: BMW
Join Date: Feb 2014
Location: Orlando

iTrader: (0)

I really need to do this with help from Don.
Appreciate 1
kaybat65.50

      03-06-2020, 09:29 AM   #6
tominizer
Lieutenant
tominizer's Avatar
Canada
75
Rep
476
Posts

Drives: 2007 Z4M Roadster
Join Date: May 2016
Location: Toronto

iTrader: (1)

Cool news. I didn't know about this
Appreciate 0
      03-10-2020, 04:43 PM   #7
mas3423
Enlisted Member
12
Rep
38
Posts

Drives: BMW Z4
Join Date: Feb 2008
Location: Central Jersey

iTrader: (0)

Send a message via AIM to mas3423
Great find! I am in the processing of sourcing one of these motors/pumps. This might be a dumb question, do they come with fluid already in the tank, or do we have to add it? The one I found, is missing the hydraulic line bolts and the tank looks empty. They are asking $125 for this.

__________________

19" Beyern Mesh Wheels / Dinan Exhaust / Dinan Stage 2 Software / AFE Intake / Umnitza LED License Plate Bulbs / Apexcone 3000k HID Fogs / Yellow Laminex / ZHP Short Shift Knob / Color Matched Stubby Antenna / 35% Tint / Valentine One Radar Detector
Appreciate 0
      05-21-2020, 09:09 PM   #8
farco
Registered
0
Rep
1
Posts

Drives: z4, 335, X5, X3,
Join Date: May 2020
Location: toronto

iTrader: (0)

BMW Z4

Hi

to replace the motor you have to take top off if you want to relocate the motor to trunk?
where did you mount it in the trunk?
Appreciate 0
      05-21-2020, 09:45 PM   #9
mas3423
Enlisted Member
12
Rep
38
Posts

Drives: BMW Z4
Join Date: Feb 2008
Location: Central Jersey

iTrader: (0)

Send a message via AIM to mas3423
I successfully finished the job last week. It it weren't for the excellent resources online, this would have not been possible. Huge thanks to Shipkiller for the incredible instructions. As expected the OEM motor was soaking wet and corroded. I am extremely happy with the replacement Mustang motor. It is very fast at opening and closing, and was a fraction of the cost of the BMW part. It even came with a bracket to mount it on. Relocating to the motor to the trunk was very simple, and did not require any additional wiring or extensions. My replacement motor/pump already had plenty of hydraulic fluid in the tank, so I did not need to add.

Just to correct the original post, reversing the positive and negative terminals on the motor, will either cause the top to open or close. Not reversing the hydraulic lines. So if you press the open button and the top closes, just reverse the positive and negative terminals.

If anyone has any questions, I would be happy to help.







__________________

19" Beyern Mesh Wheels / Dinan Exhaust / Dinan Stage 2 Software / AFE Intake / Umnitza LED License Plate Bulbs / Apexcone 3000k HID Fogs / Yellow Laminex / ZHP Short Shift Knob / Color Matched Stubby Antenna / 35% Tint / Valentine One Radar Detector
Appreciate 5
      05-27-2020, 09:00 AM   #10
cjmahone66
New Member
2
Rep
9
Posts

Drives: 2003 BMW Z4 2.5i STauto
Join Date: Jul 2014
Location: North Texas

iTrader: (0)

very nice, thanks for sharing. wish i had known about this motor option a couple years ago.
Appreciate 0
      06-26-2020, 01:37 PM   #11
rsutoratosu
Lieutenant
33
Rep
562
Posts

Drives: Z4 3.0i
Join Date: Mar 2011
Location: Chicago, IL

iTrader: (0)

Quote:
Originally Posted by mas3423 View Post
If anyone has any questions, I would be happy to help.

Lmk when I can come over and work on my broken top
__________________
-Roranji
Appreciate 0
      07-27-2020, 03:53 AM   #12
colb
Registered
Wales
2
Rep
2
Posts

Drives: BMW Z4 & Z3
Join Date: Jul 2020
Location: Newport, Wales UK

iTrader: (0)

The motor and pump can be relocated to the boot without having to remove the hood from the car. Its a bit of a struggle to get to the motor and release it from its stock location as its held in by zip ties that have to be broken by brute force. Here is a link to a very good guide on a UK forum with pictures. https://zroadster.org/threads/z4-roo...to-boot.19256/
Most motors can be revived back to working condition by soaking them in diesel to free them up, general clean and they spring back to life. To lift the plastic container that contains the motor/pump in the original location I used a long bar forced inbetween the container top and its body and using a built up pivot point in the trunk forced the container upwards till the zip ties snapped, it was easy to lift it up and out into the boot, the cables and lines are long enough to repostion it at the side of the boot in the recess next to the trunk firewall.
Appreciate 1
      07-29-2020, 12:31 PM   #13
rsutoratosu
Lieutenant
33
Rep
562
Posts

Drives: Z4 3.0i
Join Date: Mar 2011
Location: Chicago, IL

iTrader: (0)

I'm definitely going to try that this year, when the weather is cooler.. its burning out side right now.
__________________
-Roranji
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 01:28 AM.




zpost
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST