|
|
SUPPORT ZPOST BY DOING YOUR TIRERACK SHOPPING FROM THIS BANNER, THANKS! |
Post Reply |
|
Thread Tools | Search this Thread |
04-16-2012, 10:35 PM | #1 |
Lieutenant
24
Rep 495
Posts |
Help Needed, front wheel frozen to the hub!
Hey all,
I just bought new wheels and was getting ready to put them on when I found that my drivers front wheel seems to be frozen to the hub. And yes I had all the lugs off... I've had it off a few times before, but this time it just didn't budge. I only had a scissor jack so didn't want to lay into it hard, but at the end I was giving it everything I've got. Is it possible for the hub to rust to the wheel and fuze? I tried, rubber mallet, WD40 around the inner and outer hub, and lots of elbow grease and nothing.
__________________
|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit| Last edited by jdl1pt; 04-17-2012 at 01:23 AM.. |
04-16-2012, 10:47 PM | #3 |
Dog Listener
711
Rep 7,850
Posts |
Had this happen too. Took a 2x4, padded it (towel), gave the 2x4 a tap with my 10 lb sledge. The 2x4 was a 16" section, and the 16" were between the sledge and the edge of the wheel/tire. It just needed a tap (not a whack).
|
Appreciate
0
|
04-16-2012, 10:48 PM | #4 |
Commander
221
Rep 852
Posts
Drives: Z4MC/M5/640iX/M1000RR
Join Date: Nov 2010
Location: Aurora, ON, Canada
|
My suggestion is put one of the lugs back on partially so the wheel doesn't fly off when it eventually does come off and keep at it with that rubber mallet from the inside part of the wheel. And next time throw on just a bit of high-temp anti seize around the hub so you don't have this issue in the future
Edit: Padded 2x4 + rubber mallet sounds a bit better than my original suggestion like Finnegan says. |
Appreciate
0
|
04-16-2012, 10:48 PM | #5 |
Lieutenant
24
Rep 495
Posts |
__________________
|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit| |
Appreciate
0
|
04-16-2012, 10:49 PM | #6 | ||
Lieutenant
24
Rep 495
Posts |
never mind found it http://www.pbblaster.com/
Quote:
Quote:
Thanks both!
__________________
|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit| Last edited by jdl1pt; 04-16-2012 at 10:57 PM.. |
||
Appreciate
0
|
04-16-2012, 11:22 PM | #7 | |
enthusiast
48
Rep 1,695
Posts |
Quote:
|
|
Appreciate
0
|
04-17-2012, 12:04 AM | #9 | ||
Lieutenant
24
Rep 495
Posts |
Quote:
Quote:
__________________
|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit| |
||
Appreciate
0
|
04-17-2012, 12:39 AM | #10 | |
Dog Listener
711
Rep 7,850
Posts |
Quote:
|
|
Appreciate
0
|
04-17-2012, 01:21 AM | #11 | |
Lieutenant
24
Rep 495
Posts |
Quote:
I saw the wheel pin long ago. Now that I have a second set of rims, and may be swapping more often, I may pick one up. Pics of the new rims mounted will be up Thursday (fingers crossed)
__________________
|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit| |
|
Appreciate
0
|
04-18-2012, 11:41 PM | #12 |
Major
159
Rep 1,108
Posts |
Had this happen on a couple of cars. I use what I call "Donkey Kicks". Get on your butt sitting in front of the wheel and give some swift kicks with both feet on the lower edge of the wheel/tire!
|
Appreciate
0
|
04-19-2012, 12:12 AM | #13 | |
Lieutenant
24
Rep 495
Posts |
Quote:
The rubber mallet to the back of the wheel finally did the trick! Thanks everyone for your thoughts, this forum is awesome!
__________________
|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit| |
|
Appreciate
0
|
Post Reply |
Bookmarks |
Thread Tools | Search this Thread |
|
|