|
|
SUPPORT ZPOST BY DOING YOUR TIRERACK SHOPPING FROM THIS BANNER, THANKS! |
Post Reply |
|
Thread Tools | Search this Thread |
08-29-2016, 04:43 PM | #1 |
Private First Class
6
Rep 118
Posts |
Z4MC seat belt replacement
Hey guys,
I am looking to replace my lazy passenger side belt as it does not want to retract. I have already dismantled my trunk area once to install a Mediabridge unit and would like to avoid that hassle again. Have if any of you done this? Is the seat belt accessible from behind the seat? I am wondering if I can get to it by disassembling the plastic trim around the sub. Thanks! Ryan |
08-29-2016, 05:40 PM | #2 |
Lieutenant General
2426
Rep 11,667
Posts |
The belt reel is behind the rear bulkhead.
You need to remove the trims in that area
__________________
'21 M2C Hockenheim Silver
'18 718 Cayman S Lava Orange (sold) '13 E92 M3 Santorini Blue (sold) '07 Z4 M Coupe Alpine White (sold) |
Appreciate
0
|
08-29-2016, 10:54 PM | #3 |
Private First Class
58
Rep 199
Posts |
No need to dismantle the trunk. Get the rear roller sun shade removed and you will be able to access both seat belt assemblies simply by pulling back the carpet.
|
Appreciate
0
|
09-06-2016, 02:08 PM | #5 |
Major General
423
Rep 5,328
Posts |
i wish it was this easy on the roadster!
__________________
Z4MR VT2 - Clubsport build.
Multi award winning Detailing | Wrap | PPF specialists UK based - www.topwrapz.com |
Appreciate
0
|
05-07-2017, 05:35 PM | #7 |
Private First Class
6
Rep 118
Posts |
Hey guys I have finally gotten around to trying this and have hit a road block. Before I attempt to take anything else apart I thought I would seek some guidance from you. I need to remove the passenger side seat belt and have removed the B pillar cover, the trim piece directly below the B pillar and the trim piece directly above the center console.
Can you please advise on next steps? This is where I'm at: (Please excuse the dusty interior, a full detail is pending this install ) https://drive.google.com/open?id=0B5...Wp6U2hwZHo1VVk Thanks in advance! Much appreciated! Ryan |
Appreciate
0
|
05-07-2017, 06:06 PM | #8 |
Lieutenant General
2426
Rep 11,667
Posts |
You need to remove all the trim across the top in order to get the tonneau cover roller out.
Once that's out you're good
__________________
'21 M2C Hockenheim Silver
'18 718 Cayman S Lava Orange (sold) '13 E92 M3 Santorini Blue (sold) '07 Z4 M Coupe Alpine White (sold) |
Appreciate
0
|
05-07-2017, 08:41 PM | #10 |
Lieutenant General
2426
Rep 11,667
Posts |
Its been a while but IIRC, Its two pieces
one part you have to pry off with a trim tool, the other is bolted
__________________
'21 M2C Hockenheim Silver
'18 718 Cayman S Lava Orange (sold) '13 E92 M3 Santorini Blue (sold) '07 Z4 M Coupe Alpine White (sold) |
Appreciate
0
|
05-08-2017, 01:41 PM | #11 | ||
Colonel
2428
Rep 2,704
Posts
Drives: Built not Bought 04 Z4 VF
Join Date: Feb 2013
Location: Kitchener Ontario Canada
|
Quote:
Quote:
http://www.realoem.com/bmw/enUS/show...diagId=51_4916
__________________
W2A Intercooled Vortech V3Si, custom ducting, Alpha N, 60# Bosch,2.62 pulley, multi port WMI, Severn Tuning(pokeybritches), Tial, magnaflow,SS race muffler, 42 design,3.91LSD, H&R, Hotchkis,ST coils,Konis, Megan camber arms, AKG SS, Nylon mounts, Poly bushings, Carbon interior, CF Aero.APEX
|
||
Appreciate
0
|
05-08-2017, 11:28 PM | #12 | |
Private First Class
6
Rep 118
Posts |
Quote:
|
|
Appreciate
0
|
06-24-2017, 11:36 AM | #13 |
Private First Class
6
Rep 118
Posts |
So I finally got around to doing this, your tips on getting the interior trim apart were very helpful, thank you.
Turns out the belt was just twisted below the trim piece so I didn't need to replace it! It's all back together now and working in good order. Thanks again guys! |
Appreciate
0
|
Post Reply |
Bookmarks |
|
|