|
|
SUPPORT ZPOST BY DOING YOUR TIRERACK SHOPPING FROM THIS BANNER, THANKS! |
Post Reply |
|
Thread Tools | Search this Thread |
03-16-2008, 08:54 PM | #1 |
New Member
3
Rep 12
Posts |
Help, What to do?
Hi folks,
Here is my problem, I just purchased my new/used 2003 Z4, Any ideas how to prevent the lower part of the front bumper from getting scratched from going over little inclines, i.e. my driveway has a slight incline, the apron to the driveway is so small, yet even if I pull in slow, Sometimes it still hits the lower dam/bumper, Any help would be most appreciated! Thank in advance!! Bob |
03-16-2008, 09:29 PM | #3 |
lettuce
18
Rep 201
Posts |
http://leatherz.com/Merchant2/mercha...tegory_Code=Z4
i own it, it wasn't too hard to install... to avoid driveway, in addition to going slow, you also have to go at an angle. I avoid narrow driveways. |
Appreciate
0
|
03-16-2008, 11:00 PM | #4 |
Captain
57
Rep 822
Posts |
When you enter your driveway, Does the front bumper scrape if you back in the driveway?
__________________
SoCal Z Enthusiast contact me to get on the list. Events for like minded people and when you talk about your Z, we will know what you are saying. https://www.facebook.com/groups/ZSCCACalifornia/
|
Appreciate
0
|
03-17-2008, 12:13 AM | #6 | |
My favorite sign.
169
Rep 4,333
Posts |
Quote:
__________________
|
|
Appreciate
0
|
03-17-2008, 11:37 AM | #7 | |
Brigadier General
2070
Rep 4,365
Posts
Drives: '07 Z4 Coupe, '21 X3, '16 GMC
Join Date: Aug 2007
Location: Iowa
|
Quote:
If it is really that bad I am sure any good body shop could make skid plates for your car, which could be replaced when they get worn down and protect your underside at the same time.
__________________
2007 Z4 3.0si Coupe • 6 MT • Black Saphire Metallic • PP • SP
2016 GMC Sierra SLT Z71 Premium Plus 4x4 2017 Harley StreetGlide • Denim Black • V&H Tune 2021 BMW x30i • Phytonic Blue Metallic • Fully loaded |
|
Appreciate
0
|
03-17-2008, 11:39 AM | #8 |
My favorite sign.
169
Rep 4,333
Posts |
Not really...home depot cut the wood to size for me, all I had to do was put a few screws in it...no scraping
__________________
|
Appreciate
0
|
03-17-2008, 12:16 PM | #9 |
Brigadier General
2070
Rep 4,365
Posts
Drives: '07 Z4 Coupe, '21 X3, '16 GMC
Join Date: Aug 2007
Location: Iowa
|
lol, I was talking about putting the ramp out/ bringing it back in all the time. Then again I am pretty lazy when I can be. Getting out to open/close my garage door (no opener) is about all the work I care to put in
__________________
2007 Z4 3.0si Coupe • 6 MT • Black Saphire Metallic • PP • SP
2016 GMC Sierra SLT Z71 Premium Plus 4x4 2017 Harley StreetGlide • Denim Black • V&H Tune 2021 BMW x30i • Phytonic Blue Metallic • Fully loaded |
Appreciate
0
|
03-17-2008, 03:44 PM | #10 |
My favorite sign.
169
Rep 4,333
Posts |
Well...I had a garage door opener, so I guess it all evens out
__________________
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|