Official: APEX EC-7 wheel thread - Page 3

trialskid · 05-16-2012, 09:10 PM

Quote:

Originally Posted by paintpro21

18x8.5" ET35 Front with 235/40/18
18x9.5" ET22 Rear with 265/35/18 or 275/35/18

i have a brand new set of tires in the stock size i would like to use so would i need skinnier rims?

mfanatic325 · 05-17-2012, 02:20 AM

Quote:

Originally Posted by trialskid

i have a brand new set of tires in the stock size i would like to use so would i need skinnier rims?

No, you can re-use your stock tires. They just might be slightly stretched it all. Once you wear out those stock tires, then you can upgrade to wider tires

trialskid · 05-17-2012, 09:33 PM

have they released pricing yet?

007MCoupe · 05-17-2012, 11:45 PM

I'm sold.

Rawyzf · 05-22-2012, 08:06 AM

Now that pricing is out, the official question is, when is a group buy going to be lined up?

BIMMERGUY91 · 05-22-2012, 06:16 PM

Quote:

Originally Posted by Rawyzf

Now that pricing is out, the official question is, when is a group buy going to be lined up?

What he said. I am in for a group buy

trialskid · 05-22-2012, 08:19 PM

Quote:

Originally Posted by Rawyzf

Now that pricing is out, the official question is, when is a group buy going to be lined up?

where did you see the pricing

BIMMERGUY91 · 05-23-2012, 10:03 AM

Its on their website

Rawyzf · 05-23-2012, 10:09 AM

Quote:

Originally Posted by trialskid

where did you see the pricing

Quote:

Originally Posted by BIMMERGUY91

Its on their website

Yup, here you go: http://www.myapexparts.com/2012/04/2...wheel-release/

Eddy@ApexRaceParts · 05-23-2012, 10:09 PM

This thread is a technical only discussion, and we can only answer fitment questions in this section of the forum.

ZeD4Mr · 05-23-2012, 11:42 PM

Would 18x9 ET31/18x9.5 ET22 a direct fit on a stock setup Z4M?

Will Gun Metal or Hyper Black color be offered in the near future?

thanks,

BIMMERGUY91 · 05-25-2012, 11:14 AM

Paintpro, create a group buy in the sponsors classifieds!!!!!

BIMMERGUY91 · 06-11-2012, 11:24 AM

Bump for updates

Eddy@ApexRaceParts · 07-23-2012, 07:04 PM

Quote:

Originally Posted by ZeD4Mr

Would 18x9 ET31/18x9.5 ET22 a direct fit on a stock setup Z4M?

Will Gun Metal or Hyper Black color be offered in the near future?

thanks,

18x9" ET31 is too aggressive for a stock Z4M. Camber plates would be a must to keep the wheel under the fender. 18x9.5" ET22 is a direct fitment for the rear.

Gun Metal is very similar to Anthracite. Hyper Black will not be offered.

Quote:

Originally Posted by BIMMERGUY91

Bump for updates

updates would be found in the classified section. This thread must be kept to technical/fitment questions only.

GomboRombo · 07-29-2012, 02:07 PM

Quote:

Originally Posted by Eddy@ApexRaceParts

Quote:

Originally Posted by trialskid

What would the best fitment for stock suspension + tires be?

18x8.5" ET35 Front with 235/40/18
18x9.5" ET22 Rear with 265/35/18 or 275/35/18

How about the best fitment for an 07 non-M staggered with Eibach's?

Joe@ApexRaceParts · 07-30-2012, 01:45 PM

Quote:

Originally Posted by GomboRombo

How about the best fitment for an 07 non-M staggered with Eibach's?

For your car we would recommend an 18x8.5" ET35 with a 245/35/18 front tire and either an 18x9" ET42 or an 18x9.5" ET43 with a 255/35/18 rear tire.

Bammered · 07-30-2012, 06:17 PM

Can't wait to get these on my ///M !!
I'm now going apex for street and track. The arc 8's for the track and these for the street.

Question is do I try and run 265's all round? I ordered 9.5et35 front and 10et25 rear. I have ground control coil-overs and I can currently just clear (slight rubbing) 255 30 front on the CH's.

My BBS CH' will be for sale: 19" 8.5 et35 and 10 et20 rear.

Rated M Roadster · 07-30-2012, 06:47 PM

Quote:

Originally Posted by Bammered

Can't wait to get these on my ///M !!
I'm now going apex for street and track. The arc 8's for the track and these for the street.

Question is do I try and run 265's all round? I ordered 9.5et35 front and 10et25 rear. I have ground control coil-overs and I can currently just clear (slight rubbing) 255 30 front on the CH's.

My BBS CH' will be for sale: 19" 8.5 et35 and 10 et20 rear.

You can fit 265s up front with a spacer and camber; rear will be fine with 265s.

Bammered · 07-30-2012, 07:12 PM

Quote:

Originally Posted by Rated M Roadster

Quote:

Originally Posted by Bammered

Can't wait to get these on my ///M !!
I'm now going apex for street and track. The arc 8's for the track and these for the street.

Question is do I try and run 265's all round? I ordered 9.5et35 front and 10et25 rear. I have ground control coil-overs and I can currently just clear (slight rubbing) 255 30 front on the CH's.

My BBS CH' will be for sale: 19" 8.5 et35 and 10 et20 rear.

You can fit 265s up front with a spacer and camber; rear will be fine with 265s.

Yeah the rear I'm not concerned with as I'm fine with the 275 19's....up front I run -3 degrees so that should help.

I was just thinking about what I could be giving up by trying to stuff the 265 up front. I guess more tramline? I am just enticed by the idea of being able to swap tires( not rims) front to back.

Joe@ApexRaceParts · 08-02-2012, 07:03 PM

Quote:

Originally Posted by Bammered

Yeah the rear I'm not concerned with as I'm fine with the 275 19's....up front I run -3 degrees so that should help.

I was just thinking about what I could be giving up by trying to stuff the 265 up front. I guess more tramline? I am just enticed by the idea of being able to swap tires( not rims) front to back.

If you would like to run a square combination the care will behave a lot more neutrally in that it will understeer much less. The -3 degrees of camber that you currently run definitely helps the performance of the car and aids in fitting the 265/35/18 tire and 18x9.5" ET35 wheel up front. You could run a 12-15mm spacer in the rear with an 18x9.5" ET35 to have approximately the same fitment against the fender as an 18x9.5" ET22. It is possible that you may experience more tram lining but the performance benefit will far outweigh any small stretch of road with inconsistencies that would cause tram lining.

gferil · 08-24-2012, 03:21 PM

Quick picture of the wheels getting installed. So far, couldn't be happier, the wheels are gorgeous, and two of the four didn't need wheel weights, which speaks volumes for the quality of the wheel and Michelin PSS's.

ZeD4Mr · 08-24-2012, 04:31 PM

More pictures and spec PLEASE... Looks great and that's the color I want.

05-17-2012, 11:45 PM	#48
007MCoupe Major Drives: das Bierwagen Join Date: Jun 2010 Location: the 'Ring Posts: 1,347 iTrader: (4) Garage List 2007 Z4 M Coupe [0.00]	I'm sold. __________________ RPI scoop///VB3///75mm wheel studs//////Stubby///GoMiniGo///GC front sway bar///AKG Engine Mounts///AKG Trans Mounts///SS brake lines Harris Hill Road, LVMS, Ring...

05-23-2012, 10:03 AM	#52
BIMMERGUY91 Captain Drives: 2007 Sapphire Black Z4 M Coupe Join Date: Apr 2010 Location: Huntsville, AL Posts: 671 iTrader: (1)	Its on their website __________________ 07 Z4MC #1019/1815

05-25-2012, 11:14 AM	#56
BIMMERGUY91 Captain Drives: 2007 Sapphire Black Z4 M Coupe Join Date: Apr 2010 Location: Huntsville, AL Posts: 671 iTrader: (1)	Paintpro, create a group buy in the sponsors classifieds!!!!! __________________ 07 Z4MC #1019/1815

06-11-2012, 11:24 AM	#57
BIMMERGUY91 Captain Drives: 2007 Sapphire Black Z4 M Coupe Join Date: Apr 2010 Location: Huntsville, AL Posts: 671 iTrader: (1)	Bump for updates __________________ 07 Z4MC #1019/1815

08-24-2012, 03:21 PM	#65
gferil Captain Drives: 06 Z4MC Join Date: Dec 2010 Location: San Francisco, CA Posts: 697 iTrader: (5)	Quick picture of the wheels getting installed. So far, couldn't be happier, the wheels are gorgeous, and two of the four didn't need wheel weights, which speaks volumes for the quality of the wheel and Michelin PSS's. Attached Images

05-17-2012, 09:33 PM	#47
trialskid Private First Class Drives: 08 335i Join Date: Dec 2011 Location: Ontario Posts: 147 iTrader: (0)	have they released pricing yet?

05-22-2012, 08:06 AM	#49
Rawyzf Pontiac G8GT Drives: 09 Pontiac G8 GT Join Date: Mar 2010 Location: Blaine, MN Posts: 304 iTrader: (2)	Now that pricing is out, the official question is, when is a group buy going to be lined up?

05-23-2012, 10:09 PM	#54
Eddy@ApexRaceParts Drives: E30 M3, E34 540i/6, Cooper S Join Date: Jun 2009 Location: Bay Area, CA Posts: 1,514 iTrader: (3)	This thread is a technical only discussion, and we can only answer fitment questions in this section of the forum.

05-23-2012, 11:42 PM	#55
ZeD4Mr First Lieutenant Drives: MR Join Date: Dec 2009 Location: Left Posts: 324 iTrader: (6)	Would 18x9 ET31/18x9.5 ET22 a direct fit on a stock setup Z4M? Will Gun Metal or Hyper Black color be offered in the near future? thanks,

07-30-2012, 06:17 PM	#61
Bammered Track Addict Drives: E86 Z4 ///M COUPE Join Date: Jun 2007 Location: NYC/NJ Posts: 197 iTrader: (0) Garage List 2006 E86 ///M COUPE [0.00]	Can't wait to get these on my ///M !! I'm now going apex for street and track. The arc 8's for the track and these for the street. Question is do I try and run 265's all round? I ordered 9.5et35 front and 10et25 rear. I have ground control coil-overs and I can currently just clear (slight rubbing) 255 30 front on the CH's. My BBS CH' will be for sale: 19" 8.5 et35 and 10 et20 rear.

08-24-2012, 04:31 PM	#66
ZeD4Mr First Lieutenant Drives: MR Join Date: Dec 2009 Location: Left Posts: 324 iTrader: (6)	More pictures and spec PLEASE... Looks great and that's the color I want.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search