ZPOST
BMW Garage BMW Meets Register Search Today's Posts Mark Forums Read


Go Back   ZPOST > Marketplace > Sponsors Classifieds
  TireRack

SUPPORT ZPOST BY DOING YOUR TIRERACK SHOPPING FROM THIS BANNER, THANKS!
Post Reply
 
Thread Tools Search this Thread
      01-30-2011, 10:39 PM   #23
cmark8
S54^2
 
cmark8's Avatar
 
Drives: Armored Toyota SW4 TDi
Join Date: Jun 2010
Location: Sao Paulo

Posts: 449
iTrader: (8)

I was wondering if the 17" ARC8s will clear front and rear Stoptech 355mm BBK. I want to run a cheaper tire setup for my car.
__________________
cmark8 is offline   Brazil
0
Reply With Quote
      01-30-2011, 10:50 PM   #24
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

Quote:
Originally Posted by cmark8 View Post
I was wondering if the 17" ARC8s will clear front and rear Stoptech 355mm BBK. I want to run a cheaper tire setup for my car.
The 17's have enough barrel clearance for the 355mm stoptechs. We test fit 17x9's on my friends 335i after installing a 6 piston 355mm stoptech kit. The car needed a spacer for strut tube clearance, which provided caliper to spoke clearance as well. I'm not sure if a spacer is needed on the front of the Z4M. The smaller the diameter the closer the barrel/tire is to the strut, and most BMW's don't have this issue with 18" wheels, but they do with 17's. So I can't comment with 100% certainty at this time. But it sounds very do-able.
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      01-31-2011, 01:55 AM   #25
kaiv
Major
 
Drives: E92 M3
Join Date: Mar 2010
Location: San Diego, CA

Posts: 1,232
iTrader: (15)

Is there any chance for a 17x9.5 ET30/35?
kaiv is offline   United_States
0
Reply With Quote
      01-31-2011, 01:14 PM   #26
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

Quote:
Originally Posted by kaiv View Post
Is there any chance for a 17x9.5 ET30/35?
No, we don't produce custom/one off fitments. To keep pricing this low, wheels have to be made in the hundreds for each minor change including finish. We ordered over 3000 wheels recently so that we could keep pricing this low, yet have a relatively wide range of available fitments.
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      02-02-2011, 03:47 PM   #27
Bammered
Track Addict
 
Bammered's Avatar
 
Drives: E86 Z4 ///M COUPE
Join Date: Jun 2007
Location: NYC/NJ

Posts: 197
iTrader: (0)

Garage List
Send a message via MSN to Bammered
Interested.. Whats the group buy price?
Bammered is offline   United_States
0
Reply With Quote
      02-02-2011, 08:16 PM   #28
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

Quote:
Originally Posted by Bammered View Post
Interested.. Whats the group buy price?
The Group Buy details are listed here: Price depends on what discount tier is reached. We have about 20 day for people to sign up, so the discounts should be deep. We just closed a 1 series group-buy that ended on the 3rd tier discount level.

http://www.zpost.com/forums/showthre...=1#post8828462
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      05-23-2011, 02:45 PM   #29
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

We've updated this thread with new product photos:

Hyper Silver:


Hyper Black:


Anthracite:


Satin Black:


http://www.apexraceparts.com/Z3-Z4-Series_c_41.html
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      05-31-2011, 08:58 PM   #30
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

in stock and ready to ship!
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      06-30-2011, 09:48 PM   #31
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

We still have these ready to ship!
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      07-04-2011, 02:28 AM   #32
jdl1pt
Lieutenant
 
Drives: Z4M coupe 2007 IL Blue
Join Date: May 2010
Location: Oakland, CA

Posts: 482
iTrader: (5)

Quote:
Originally Posted by paintpro21 View Post
We still have these ready to ship!
Possible for locals to see in person before purchase?
__________________

|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit|
jdl1pt is offline  
0
Reply With Quote
      07-06-2011, 07:17 PM   #33
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

Quote:
Originally Posted by jdl1pt View Post
Possible for locals to see in person before purchase?
Yes, you can check out the finishes here. We are not always in the warehouse/office so you'd want to call ahead to make an appointment so that we can guarantee someone will be here at the time you'd like to come by.
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      07-06-2011, 11:06 PM   #34
jdl1pt
Lieutenant
 
Drives: Z4M coupe 2007 IL Blue
Join Date: May 2010
Location: Oakland, CA

Posts: 482
iTrader: (5)

Quote:
Originally Posted by paintpro21 View Post
Yes, you can check out the finishes here. We are not always in the warehouse/office so you'd want to call ahead to make an appointment so that we can guarantee someone will be here at the time you'd like to come by.
Sweet, thanks! Will give you a call before heading out.
__________________

|OEM Strut bar|ZHP Knob lighted|RPI Scoop|Zeckhausen Modified CDV|DIY Clutch Stop|Camber shim kit|
jdl1pt is offline  
0
Reply With Quote
      08-11-2011, 08:18 PM   #35
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

These are on stock and ready to ship in all sizes and finishes!
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      08-14-2011, 03:27 AM   #36
Z4-PM
New Member
 
Drives: Z4MC
Join Date: Jul 2011
Location: Toulouse

Posts: 13
iTrader: (0)

I would like to keep the stock tires (not much tolerance in France by authorities to change circumference), namely F: 225/45/18 and R:255/40/18, so will they fit on ARC8 F:8.5/18 ET35 and R:9.5/18 ET22 ?
Z4-PM is offline   France
0
Reply With Quote
      02-29-2012, 07:50 PM   #37
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

We have these in stock and ready to ship!

18x8.5" ET38 Front
18x9.0" ET42 Front
18x9.5" ET22 Rear

18x9.5" ET35 is only available in Anthracite and Satin Black until the end of March

18x10" ET25 is only available in Hyper Silver and Anthracite until the end of March


Quote:
Originally Posted by Z4-PM View Post
I would like to keep the stock tires (not much tolerance in France by authorities to change circumference), namely F: 225/45/18 and R:255/40/18, so will they fit on ARC8 F:8.5/18 ET35 and R:9.5/18 ET22 ?
Yes, those tire sizes would fit
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      03-22-2012, 04:30 PM   #38
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

20 pallets of wheels are arriving Monday or Tuesday. We will have every size/finish back in stock again.

Back-orders are accepted on the site at this time

http://www.apexraceparts.com/Z3-Z4-Series_c_41.html
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      03-22-2012, 11:10 PM   #39
RandysV10
MPOWERD
 
RandysV10's Avatar
 
Drives: 2010 M6
Join Date: Nov 2010
Location: Cloud Nine

Posts: 338
iTrader: (0)

Garage List
2006 Z4M  [0.00]
2010 BMW M6  [0.00]
Will the 18x9.5 et35 square set up with 265/35/18's R-Comps fit with a BBK? Spacers needed?
__________________
2010 Dinan M6 Coupe--2006 Z4MC--1994 E36/M3 Track Prepped
BMWCCA #442445

YouTube Channel: http://www.youtube.com/user/Randy23185
RandysV10 is offline  
0
Reply With Quote
      03-26-2012, 07:06 PM   #40
Eddy@ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: E30 M3, 2011 335d
Join Date: Jun 2009
Location: Bay Area, CA

Posts: 1,599
iTrader: (5)

Quote:
Originally Posted by RandysV10 View Post
Will the 18x9.5 et35 square set up with 265/35/18's R-Comps fit with a BBK? Spacers needed?
It depends on the BBK. Usually a 5mm spacer is needed, but the spacer also provides the needed strut tube clearance when used with r-compounds.
Eddy@ApexRaceParts is offline  
0
Reply With Quote
      08-03-2012, 01:41 PM   #41
David@ApexRaceParts
BimmerPost Supporting Dealership

 
David@ApexRaceParts's Avatar
 
Drives: M3
Join Date: Jun 2012
Location: Bay Area

Posts: 1,360
iTrader: (0)

We just restocked on ARC-8s in plenty of sizes! Give us a call if you need a set!

David@ApexRaceParts is offline  
0
Reply With Quote
      08-13-2012, 05:09 PM   #42
David@ApexRaceParts
BimmerPost Supporting Dealership

 
David@ApexRaceParts's Avatar
 
Drives: M3
Join Date: Jun 2012
Location: Bay Area

Posts: 1,360
iTrader: (0)

We have plenty of the ARC-8s in stock currently for your Z4 and Z4M!



Give us a call if you have any questions regarding fitment!
David@ApexRaceParts is offline  
0
Reply With Quote
      08-17-2012, 01:51 PM   #43
ApexRaceParts
BimmerPost Supporting Dealership

 
Drives: M3
Join Date: Jun 2012
Location: Bay Area

Posts: 729
iTrader: (0)

We have plenty of ARC-8's in stock in 17" and 18" Z4 fitments! Please call us for any questions regarding fitment.



Last edited by ApexRaceParts; 08-17-2012 at 02:06 PM.
ApexRaceParts is offline  
0
Reply With Quote
      08-17-2012, 02:49 PM   #44
Finnegan
Major General
 
Finnegan's Avatar
 
Drives: Sapphire Black/Black Z4Mc
Join Date: Oct 2008
Location: At the track..or wishing I were at the track

Posts: 6,357
iTrader: (17)

Got my ARC-8s (18 x 9, and 18 x 10) and will post pics in another part of the forum as soon as I have time to get them installed (work has been crazy the past week).

Great experience with the Apex team too--from questions/answers, quick responses, and fast shipping (and excellent packaging as well)!
Finnegan is offline   United_States
0
Reply With Quote
Post Reply

Bookmarks

Tags
apex, arc-8, flow formed, track wheels, wheels

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -5. The time now is 12:21 PM.




zpost
Powered by vBulletin® Version 3.7.0
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST